ANTHEM INTEGRATED 225 STEREO AMPLIFIER - SRC ELEKTRONİK HI-FI & HI-END & HOME CINEMA ONLINE SATIŞ NOKTASI

PHONO PREAMPLIFIER
The phono preamplifier is suitable for moving magnet and high-output moving coil cartrdiges
Input Impedance	47 k
Input Capacitance	100 pF
Maximum Input	18 mV at 20 Hz, 140 mV at 1 kHz, 160mV at 20 kHz
Gain (at 1 kHz)	35 dB
Crosstalk (at 1 kHz)	80 dB
RIAA Response	+/- 0.5 dB (100 Hz to 20 kHz); -1 dB (20 Hz)
THD+N (at 1 kHz, 5 mV input)	0.05%
S/N Ratio (ref. 5 mV at 1 kHz, IEC-A filter)	83 dB

PREAMPLIFIER
Input Impedance	30 k
'Pre-Out' Output Impedance	560
'Rec-Out' Output Impedance	100
Rated Input	1.0 Vrms
Maximum Input	7.6 Vrms
Minimum Load	5 k
Rated Output (100 k load)	1.0 Vrms
Maximum Output (100 k load)	7.6 Vrms
Headphone Output	500 mW into 32 at 0.03% THD+N
Channel Separation (at 1 kHz)	75 dB
Crosstalk Between Inputs (at 1 kHz)	72 dB
XLR Pin Configuration	Pin 1: Ground; Pin 2: Positive; Pin 3: Negative
Frequency Response and Bandwidth	20 Hz to 20 kHz (+0, -0.1 dB); 1 Hz to 170 kHz (+0, -3 dB)
THD+N (at rated input and output, 80 kHz BW)	0.003%
IMD (CCIF at 15 kHz and 16 kHz)	0.0005%


S/N Ratio (A-weighted, ref 2.0 Vrms)	105 dB

POWER AMPLIFIER

(per channel, continuous RMS, 20 Hz to 20 kHz, <1.0% THD)

Frequency Response

20 Hz to 20 kHz (+0, -0.15 dB)

Bandwidth

1 Hz to 200 kHz (+0, -3 dB)

THD+N

0.01% at 1 kHz, 0.03% at 20 kHz (100 W into 8 )

Power Bandwidth

< 10 Hz to 100 kHz (+0, -3 dB, 200 W into 8 )

Slew Rate

25 V/µs

Headroom

1.4 dB (8 ), 2.8 dB (4 )

Damping Factor

80 at 1 kHz (ref. 8 )

S/N Ratio (A-weighted, ref 225 W)

105 dB

Crosstalk

> 57 dB (100 Hz to 10 kHz)

Voltage Gain

29 dB

POWER REQUIREMENTS
Power Consumption (8 load)
	Maximum	800 W
	Typical	300 W
Fuse Rating (Fuse is internal)		Anthem serviceable only
Low Voltage Version: In countries where the line voltage is 120V, this product operates from a single phase AC power source that supplies between 108V and 132V at a frequency of 60 Hz.
High Voltage Version: In countries where the line voltage is 220V, 330V or 240V, this product operates from a single phase AC power source that supplies between 216V and 264V at a frequency of 50 or 60 Hz.

Advanced Load Monitoring (ALM)

Anthem^® integrated amplifiers are designed to perform flawlessly - offering stunning musicality, tonal

neutrality and incredible dynamics while driving any speaker load reliably under real-world conditions! The

power supply is conservatively rated and the amplifiers run cool for greater reliability, but we didn't stop there.

These amplifiers feature our ALM (Advanced Load Monitoring) circuitry which protects sensitive output

devices by constantly monitoring temperature, current and voltage to ensure optimum long-term performance.

ALM is totally non-invasive - it is not in the signal path and only engages in the most extreme circumstances

to protect the amplifier from damage by maintaining the safe operating area of the output devices. Buyer

beware however! Not all amplifier manufacturers have sophisticated load-monitoring provisions. Many have

saved the added cost, leaving their output devices unprotected, choosing instead to use the amplifier's output

devices as "fuses." At Anthem, ALM is just one of the ways in which our products provide owners with years of reliable service.